| | What is the Difference?Roadster, Hardtop, Standard Top or Convertible Car?
 Note: These replacement seat belts are universal fit and do NOT have electrical wiring, so they cannot be electrically wired to alarms or airbags. Please view our detailed installation instructions and also examine your vehicle to determine if the seat belt is compatible with your application.Click to view our SeatBelt Hardware Page.  Safety tested and approved, sewn, assembled, packaged in the USA. |
 | Roadster 3-Point Seat Belts - WELR-N
Roadster
The photo above shows a roadster (convertible cars that do not have much of, or any back seat). Roadsters include most MG's Triumph, Alfa Romeo, Fiat, some years and models of Corvette and more. These belts are designed to be installed with the retractor unit anchored just below the bottom of the window and behind the shoulder rather than on the floor (recommended when there just isn't enough room near the floor to fit the 4" x 4" x 3" retractor unit). These are universal fit belts, so they are perfect for most roadsters and certain mid to late 1970's Ford Trucks. If you have a roadster or one of the mentioned trucks, then you need to purchase our WELR-N seatbelts below.
Important: All belts should be fastened to vehicle achorage points provided by the vehicle manufacturer. If your vehicle has never had 3-point seatbelts installed, then before installing these aftermarket seat belts, special retrofitting procedures must be taken.
Choose either bench or bucket seat application. All of our belts work on either the driver or passenger side of your car and are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 approved. Price includes 1 seat belt for one seat / passenger.
Your Choice for Bucket Seats: 8" or 11" Rigid Sleeve End for Low or High Bucket Seats.
Optional hardware kit includes Angle Bracket, #212 Bolt Kit Mounting Hardware & Mounting Plate. Click Here to view.
Click Here to view a photo of the type of end that you get with the "Bucket Seat" option.
Click Here to view a photo of the type of end that you get with the "Bench Seat" option.
Click Here to see installation instructions!
 Click Here to Enlarge Seat Belt Photo!
* Roadster 3 Point Retractable Seat Belt WELR-N (Extends to 113")
| | | Hardtop Seat BeltsHardtop
The photo above shows a mustang that has a Hardtop which are commonly found with early model Camaro, Falcon, Mustang cars etc. The door-post in a hardtop does NOT go above the bottom of the window (it stops at the top of the door) as shown above circled in red. What is circled in red is the chrome piece for the back window; it is NOT the door-post. So if your car matches the description above, and you are looking to buy 3-point retractable seat belts, then you have a "hardtop" and you can choose either of the 2 seatbelts below depending on the installation method. (You can see in the "Standard Top" photo shown below, what it looks like when the door-post goes all the way up to the roof of the car as in all Standard Top cars.)
Installation Options
1. You can have the shoulder anchor mounted above the window into the roof. This requires our WELR seatbelts (1st belt found below).
Or
2. You can have the shoulder anchor mounted just below the bottom of the back window and behind the shoulder. For this you would want to purchase our I-3207 seat belts (2nd belt found below). |
Important: All belts should be fastened to vehicle anchorage points provided by the vehicle manufacturer. If your vehicle has never had 3-point seatbelts installed, then before installing these aftermarket seat belts, special retrofitting procedures must be taken.
All of our belts work on either the driver or passenger side of your car and are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 approved.
For Bucket Seats You Can Choose Either: 11" or 8" Rigid Sleeve End for High or Low Bucket Seats.
Price includes 1 seat belt for one seat / passenger. Optional hardware kit includes Angle Bracket, #212 Bolt Kit Mounting Hardware, Shoulder Bolt & Mounting Plate. Click Here to view.
Click Here for Installation Instructions for 3 Point Retractable Belts!
Click Here to view a photo of the type of end that you get with the "Bucket Seat" option.
Click Here to view a photo of the type of end that you get with the "Bench Seat" option.
 Click Here to enlarge photo!
Option #1. Three Pt. Retract. for Hardtop Roof Install WELR (Extends to 140")
| | | Shoulder Anchor Below Side Window - i3207
 Want to see where the shoulder anchor attaches for installation option # 2, in the interior of the car? Click Here
Click Here to see installation instructions!
All of our seatbelts are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 safety approved and work in either driver or passenger side positions. You Can Choose from 2 Bucket Seat Rigid End Lengths: 11" or 8" Rigid Sleeve End for High or Low Bucket Seats.
The price shown is for one seatbelt for one seat / passenger.
Optional hardware kit includes Angle Bracket, #212 Bolt Kit Mounting Hardware, Shoulder Bolt & Mounting Plate. Click Here to view.
Click Here to view a photo of the type of end that you get with the "Bucket Seat" option.
Click Here to view a photo of the type of end that you get with the "Bench Seat" option.
Option #2. Hardtop Three Pt. Retractable - Anchors Below Side Window - i3207 (Extends to 120")
| | | 3-Point Retractable Seat Belt - WELRStandard Top
Most newer vehicles that are not convertibles are "Standard Top" cars. The red circle in the photo above shows that Standard Top cars have door-posts that go from the frame at the bottom of the car, all the way up to the roof of the car. This is a solid post where the shoulder anchor is attached. If you are looking to buy some 3-point (both lap and over the shoulder) seatbelts that are retractable, and you have a "Standard Top" car as shown above, then you need to purchase our WELR belts below.
Price shown is for 1 seatbelt for one seat / person. All of our belts work on either the passenger or driver side and are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 safety approved. Our restaints are universal fit aftermarket seat belts, so they fit on most cars. Optional hardware kit includes Angle Bracket, #212 Bolt Kit Mounting Hardware, Shoulder Bolt & Mounting Plate. Click Here to view. Choose Bench or Bucket Seat Application.
Click Here to view a photo of the type of end that you get with the "Bucket Seat" option.
Click Here to view a photo of the type of end that you get with the "Bench Seat" option.
For high middle consoles (17" or more when measured from top of console to the floor), one 6 inch extension bracket # 6-AB is required for each seat belt installed (with high console). Click Here to see how it attaches to the seat belt end.
Click Here for Installation instructions for the 3 Point Retractable Belt
Click Here to enlarge photo!
Standard Top Three Pt. (Shoulder and Lap) Restraint WELR (Extends to 140")
| | | Convertible 3-Point Seat Belts - i-3207
Convertible Top
Not to state the obvious, but a convertible top is what is known as a convertible, as shown above. If you want to purchase a 3-point (both lap and over the shoulder) retractable seat belt, and you have a convertible that has a normal size back seat, then you need to purchase our
I-3207 seat belts below. Choice of: 11" or 8" Rigid Sleeve End for High or Low BUCKET Seats. All of our seatbelts are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 safety approved and work in either driver or passenger side positions. The price shown is for one seatbelt for one seat / passenger. Important: All belts should be fastened to vehicle achorage points provided by the vehicle manufacturer. If your vehicle has never had 3-point seat belts installed, then special retrofitting procedures must be taken before installing these aftermarket seat belts. Optional hardware kit includes Angle Bracket, #212 Bolt Kit Mounting Hardware, Shoulder Bolt & Mounting Plate. Click Here to view.
Want to see where the shoulder anchor attaches in the interior of the car? Click Here
Click Here to view a photo of the type of end that you get with the "Bucket Seat" option.
Click Here to view a photo of the type of end that you get with the "Bench Seat" option.
Click Here to see installation instructions!
Convertible Three Point Retract. i3207 (Extends to 120")
| |
We ship worldwide to Australia (AU), Canada, Denmark, Finland, France, Iceland, Ireland, Japan, Mexico Netherlands, New Zealand (NZ), Portugal, South Africa, Spain, United Arab Emirates (UAE) and the United Kingdom (UK) and more.
Disclaimer. Please read: This product is sold without warranty expressed or implied. No warranty or representation is made as to the product's ability to
protect the user from any injury or death in any manner of use. The user assumes that risk. The effectiveness of this equipment is directly related to the manner in which it is installed, used, and/or maintained. Proper installation is
solely the responsibility of the installer, and will not be assumed by Wesco Performance Inc.All Gear Seat Belt
WebMaster
|
Click Here to Enlarge Seat Belt Photo!
Click Here
